Parts for Felco pruner with rotating handle model 7 (F7)

Felco pruners last forever, but years of hard use and repeated sharpening will eventually wear down even the hardest steel blade. If your blades are chipped or cracked, your pruners no longer close all the way to the tip or you can hardly tell that there was a wire-notch at the back of the blade, then it is time for a replacement blade. You won't believe the difference it makes. Made in Switzerland.

Genuine Felco replacement blade for the Felco 7, 8 and 19 pruners. Includes 7-6 screw. Made in Switzerland.

Are your pruners listless and unresponsive? Do they open slowly or not at all? Put the spring back in your pruners. Pruner springs should be replaced every year for best performance. Made in Switzerland. Contains two springs (2-11).

Contains center bolt (7-8) and nut (2-9), locking segment (2-16) and screw for locking segment (7-7). Made in Switzerland.

Give your beloved Felco pruner a tune-up. This kit has everything you need to spruce up your pruner and keep it working smoothly for years to come. Contains catch plate (2-15); thumb catch (2-12), spring washer (2-13) and screw (2-14); upper, flat shock absorber (2-18) and lower, rounded shock absorber (2-20). Made in Switzerland. The 2-14 screw may not fit older pruners.

Worn or hardened shock absorbers can make pruning a pain in the wrist. For pain-free pruning replace your shock absorbers at least once a year. Contains 4 upper (2-18) and 6 lower (2-20) shock absorbers. Fits all Felco pruners that have shock absorbers. Made in Switzerland.

Includes bushing (2-10), blade pins, bumper and edging ring (2-19), thumb catch (2-12), spring washer (2-13), screw for catch(2-14) and non-slip rubber coating. Made in Switzerland.

Made in Switzerland.

Requires riveting. Used as a last resort to replace the cutting blade pins if the pins are lost or damaged. Once the cutting blade is riveted on, future blade replacement will require removing and replacing rivets. Made in Switzerland.

Made in Switzerland.

Did you let the locking segment stay loose too long? That’s how you lose the lock nut. Don’t freak out - buy a new nut and save your trusty tool. Made in Switzerland.

Made in Switzerland.

While replacing the thumb catch, make sure you replace the spring washer too. It holds the catch still so it stays locked when locked and stays unlocked when in use. This part may not fit older model pruners.

Does your thumb catch swing freely, locking your pruner during use? There's an easy solution: You need a new spring washer. Don't over-tighten the screw, fix it right: replace the spring washer.

While replacing the this screw, make sure you replace the spring washer too. It holds the catch still so it stays locked when locked and stays unlocked when in use. This part may not fit very old Felco pruners.

This seemingly simple part is the heart of your pruner. It acts as a washer for the center bolt and nut and also for the locking segment. It is held fast by the screw for locking segment and has a notch where the catch is caught. Without this simple, flat plate your pruners will not function. Three cheers for the catch plate! Made in Switzerland.

Made in Switzerland.

Made in Switzerland.

Made in Switzerland.

Made in Switzerland.

Made in Switzerland.

Made in Switzerland.

Over time the rubber coating on your pruner handles tends to get chipped, worn and torn. Spruce up the look and give yourself a firmer grip. Remove the old coating and slide on a new one. Use warm soapy water to help slide the new coating on smoothly. A little acrylic glue or epoxy around the edges will keep the new coating permanently in place. Made in Switzerland.

Used for adjustment and maintenance of Felco pruners and loppers. Just the right shape for tightening or loosening the center nut. The correct thickness for fitting the screw slots on older models. On newer models use the handy hexagon-shaped cut-outs for slip-free adjustment of all the nuts and bolts on your Felco pruner or lopper.